Cutting Force Modelling for Drilling of Fiber-Reinforced CompositesReport as inadecuate

Cutting Force Modelling for Drilling of Fiber-Reinforced Composites - Download this document for free, or read online. Document in PDF available to download.

Lausanne: EPFL, 2012

Although used in a very large variety of applications, drilling is one of the most complex and least understood manufacturing processes. Most of the research on drilling was done in the field of metal cutting for mechanical parts since, in this case, high precision and quality are needed. The use of composite materials in engineering applications has increased in recent years, and in many of these applications drilling is one of the most critical stages in the manufacturing process. This is because it is among the last operations in the manufacturing plan of composite parts. Delamination and extensive tool wear are among the problems which drilling of composite materials are currently facing. A major difference between metallic and composite plates is their structure: isotropic for metals and anisotropic for composite materials; meaning that while for metallic materials all the structure will respond in a similar manner under the machining loads, the composite structure will have localized responses from the same loads, leading to defects in the internal structure of the remaining work-piece material (i.e. delamination). Delamination can lead to failure in use and parts with such defects are usually discarded. Delamination is not usually visually detectable and special testing is necessary, affecting the costs of the final parts. Delamination during drilling was found to occur at tool entry (peel-up) or tool exit (push-out) and depends on the loads at inter-laminar level. The work presented in the current thesis focuses in providing reliable information about the thrust and torque distribution along the drill radius (and work-piece thickness) during drilling for varying cutting parameters, drill geometry and work-piece material. Such data should assist in the development of delamination models capable of capturing the influence of the drill geometry and cutting parameters on delamination onset and propagation during both exit and entry of the drill in the work-piece. A cutting force model is proposed to obtain the elementary cutting force distribution along the drill radius which is able to account for changes in axial feed rate and drill geometry. Based on oblique cutting, forces are considered on both rake and relief faces. A generic relationship in the form of a transformation matrix is developed to relate oblique cutting to drilling, valid for any drill geometry. The mathematical description of the drill geometry in the scope of cutting force modeling has been revised. The kinematics of the drilling process is now taken into account for (i) all geometrical parameters of the drill and for (ii) the elementary cutting forces decomposition. Additionally, a new drill type and its geometric features have been described mathematically and the definition of the geometrical parameters has been generalized so that other drills types or variations could be easily implemented into the model. It proved therefore possible to adopt simpler expressions for the empirical force coefficients of the cutting force model. Up to four empirical coefficients are used, which are calculated from experiments for each work-piece material and drill type. Most experimental investigations on drilling fiber reinforced composites analyze only the total thrust and torque generated during drilling or separately the forces caused by the chisel edge and cutting lips by drilling with or without a pilot hole. The later type of analysis suggested that is possible to obtain more detailed information about the distribution of the loads in drilling from the analysis of the forces variation during tool entry into the work-piece. Pursuing this direction, an experimental analysis method is proposed to obtain the axial and tangential elementary cutting force distribution along the tool radius or work-piece thickness. The cutting force distribution obtained experimentally was used to calibrate the cutting force model, rather than the total thrust and torque. The experimentally obtained cutting force distribution can also be used alone for analyzing the drilling process (i.e. the loads distribution among the plies of the composite laminate and how this load is influenced by changes in the drill geometry and the cutting conditions).

Keywords: drilling ; fiber reinforced composites ; cutting forces ; perçage ; composites renforcés de fibre ; effort de coupe Thèse École polytechnique fédérale de Lausanne EPFL, n° 5289 (2012)Programme doctoral Systèmes de production et RobotiqueFaculté des sciences et techniques de l'ingénieurInstitut de génie mécaniqueLaboratoire des outils informatiques pour la conception et la production Reference doi:10.5075/epfl-thesis-5289Print copy in library catalog

Author: Lazar, Mihai-BogdanAdvisor: Xirouchakis, Paul


Related documents